Configuring an Agent
Once the agent has been installed, you have to configure it.
If the target is a IaaS (a cloud infrastructure), you only have to specify one thing, the target ID.
All the other parameters will be set dynamically by the DM or the IaaS itself.
The agent comes with a default configuration that needs to be updated.
Even if the configuration is wrong, the agent will keep on running (in a degraded mode).
The configuration is persisted by the OSGi container. It is restored upon restart.
Configuration parameters can be changed at runtime, without rebooting.
This configuration is made of two parts:
-
First, there is the configuration of the agent itself.
It is associated with the PID net.roboconf.agent.configuration. -
Then, there is the configuration of its messaging (the way it will interact with other agents and with the Deployment Manager). The associated PID depends on the messaging type specified in the agent’s configuration. As an example, if the agent uses RabbitMQ, then the PID will be net.roboconf.messaging.rabbitmq. Generally, messaging configurations should have PIDs that begin with net.roboconf.messaging.
If the agent’s target-id property is set to one of the iaas-… values, then you do NOT have to configure other properties. They will be passed by the DM through cloud mechanisms (e.g. with CloudInit).
There are 2 ways of updating the agent’s configuration.
Configuring the messaging is discussed on this page.
Config Admin
If you installed the agent as bundles, you can use Config Admin to update the agent’s parameters.
These pages give information about this mechanism.
- http://wiki.osgi.org/wiki/Configuration_Admin
- http://felix.apache.org/documentation/subprojects/apache-felix-config-admin.html
- http://www.osgi.org/javadoc/r4v42/org/osgi/service/cm/ConfigurationAdmin.html
The ID of the managed services for the agent match the PIDs given before.
File Install
If you installed the agent in a Karaf distribution, there are two ways.
The first one consists in editing (or creating) the /etc/net.roboconf.agent.configuration.cfg file.
A sample is given below.
# The target ID.
# Depending on its value, the following parameters may be read from
# another location than this file. This is the case for Amazon Web Services
# Microsoft Azure and Openstack.
#
# Possible values are:
# * iaas-ec2
# * iaas-openstack
# * iaas-vmware
# * iaas-azure
# * embedded
#
target-id =
# The application name.
application-name =
# The name of the root instance associated with this agent.
root-instance-name =
# The IP address of the agent.
# This is useful if the machine has several network interfaces.
ip-address-of-the-agent =
# The type of messaging we use: RabbitMQ.
messaging-type = rabbitmq
The second solution consists in using Karaf’s web console.
The parameters can be edited under the OSGi > Configuration menu.
Look for the net.roboconf.agent.configuration key and double-click it. A dialog will show up
listing all the parameters in a form.
Agent Parameters
The following table summers up all the agent parameters.
| Property | Description | Notice | Mandatory |
|---|---|---|---|
| target-id | The target ID. Some cloud infrastructures provide mechanisms to store information for the VM. On some IaaS, the DM passes information to the agent through these means. It implies that a part of the agent configuration is read from an external location. | See the next section. | yes |
| application-name | An agent is associated with a single application. | Depending on the target ID, its value can be retrieved from user data. | yes |
| root-instance-name | Within an application, machines are represented by a root instance. This parameter is the name of the instance associated with this agent. | Depending on the target ID, its value can be retrieved from user data. | yes |
| ip-address-of-the-agent | The IP address of the agent’s machine. | This is useful if the machine has several network interfaces. | no |
| messaging-type | The kind of messaging used by the agent. | - | yes |
These parameters are persisted and restored upon restart.
However, depending on the target ID, some values may be overridden.
Target ID
The target ID indicates on which target the agent runs.
Normally, the agent parameters should be hard-written in configuration files. However, each agent has its own configuration.
Some settings are the same for all the agents (such as the messaging parameters). And some others are specific.
The couple application name and root instance name are unique. Two agents cannot have the same values for these 2 parameters.
Instead of hard-coding these parameters, it is possible to let them blank. And the DM will pass them to the agents. This is only possible in cloud infrastructures, since they support, in one way or another, a mechanism of user data. When one creates a VM (virtual machine) from a virtual image, it is possible to pass data to the new VM. Once the VM is running, it can access these data and do whatever it needs with.
To summer it up, when the target-id property is set to one of the iaas-… values, then you do NOT have to configure other properties. The agent will retrieve its configuration from user data and overwrite its configuration.
Let’s take an example with Amazon Web Services.
We assume we created a virtual image with a Roboconf agent. This one was partially configured. It has the right target ID.
Other settings are invalid or incomplete.
- In the DM, we have a root instance called “my-root” in the “my app” application.
It is associated with a component that designates an EC2 VM. - We request the DM to create the “my root” instance.
It calls the right API in EC2 and sets user data for the new VM (application name = my app, root-instance-name = my-root, plus the messaging parameters). - Once the VM is up, the agent starts, the OSGi configuration is injected in the agent.
- Since the target ID is iaas-ec2, the agent then reads the user data in EC2, thus completing its configuration.
User data override the following parameters.
- application-name
- root-instance-name
- ip-address-of-the-agent
- All the messaging parameters (used in other configuration files).
User data are used with almost all the cloud infrastructures.
The only IaaS it does not work with is the embedded one.
If the agent took its configuration in user data, you can update the parameters AFTER the agent started through Config Admin or through the *.cfg file.
Notice that if you stop the agent and restart it, and that its target ID involves user data, the agent will once again read these user data.
Maven Snapshots Resolution
If you need to install snapshot bundles in your agent distribution, you may have to configure the way they are resolved. Please, refer to this page to find more information about snapshots resolution. It indeed works the same way for both the DM and agents (since it is a Karaf configuration).